Skip to content
Chux Electrical Services

Switchboard upgrades in Geelong

An old switchboard can be a safety risk, and it often stops solar, a battery or an EV charger going in. We inspect your board, explain what it needs and quote the upgrade ourselves.

A Chux installer in a cap and sunglasses on the roof

Chux Electrical upgrades switchboards across Geelong, the Surf Coast and the Bellarine. We are a local team based in Breakwater, owned by Colin Norris and licensed under REC 24227. The person who quotes your job does the work, with no subcontractors, and every quote is free, on site and a fixed price in writing.

01

What a switchboard does and why it ages

Your switchboard is where power enters the house and gets split into circuits for lights, powerpoints, the oven and everything else. It also holds the protection devices that cut the power when something goes wrong.

Older boards were built for far fewer appliances than a modern home uses. Back then there was no air conditioning in every room, no induction cooktop, no home office and no EV in the garage. Over the years extra circuits get added to boards that were never meant to take them.

The result can be a board that is crowded, hot, noisy or missing the safety devices we now expect. Upgrading it is one of the more worthwhile electrical jobs you can do for a house.

02

From ceramic fuses to safety switches

Many older Geelong homes still have a board with ceramic fuse carriers. When a fuse blows, you replace the wire or the cartridge. These boards can work for a long time, but they have limits.

A fuse protects the wiring from overload. It does not protect you from electric shock. A safety switch, also called an RCD, monitors the current and cuts the power in a fraction of a second if electricity is leaking, for example through a person. Current wiring rules call for RCD protection on power and lighting circuits in new work.

Moving from fuses to circuit breakers and safety switches gives you faster protection, easier resets and a board that can carry the loads of a modern house.

03

Why solar, batteries and EV chargers often need a board upgrade

Adding solar or a battery means new equipment connecting into your board and your main supply. Your inverter or battery needs its own protected circuit, and the board must have room, the right ratings and a safe layout for it.

If the board is full, damaged, uses old fuses or does not meet current requirements, the installer cannot connect to it. We would rather tell you that at the quote stage than on installation day.

The same applies to an EV charger. A charger is a big, steady load that can run for hours. It needs a dedicated circuit with the right protection, and some older boards simply cannot support it.

Doing the board first, or at the same time, can cost less overall than coming back for it later. A switchboard upgrade is quoted separately from the solar, battery or charger, so you can see each cost on its own. If you are planning any of these, see our solar, battery and EV charger pages, and ask us to look at your board during the quote.

04

Signs your switchboard needs work

You do not need to be an electrician to spot a tired board. These are the common warning signs. If the problem is a fault, such as a safety switch that trips at random, finding it is charged by the hour; a full upgrade is quoted.

  • Ceramic fuses or a board with no safety switches
  • Safety switches or breakers that trip often, or will not reset
  • A burning smell, scorch marks or a warm board
  • Buzzing or crackling from the board
  • Lights that dim or flicker when an appliance starts
  • A board that is full, with no space to add circuits
  • Visible damage, rust or moisture inside the cabinet
  • Plans for solar, a battery, an EV charger or a renovation

05

How we do the upgrade

We come out, open up the board, check what is behind it and talk through your plans. You get a free quote that sets out exactly what is included.

On the day, the power to the house is off while the new board is installed. We tell you how long that will be in advance so you can plan around it. When the new board is in, we test every circuit and safety switch, label everything and walk you through it.

06

What affects the cost of a switchboard upgrade

The price depends on how many circuits your home has, how many safety switches and breakers are needed, the condition of the wiring coming into the board, and whether the meter box or supply needs any work.

A bigger home or a board that has to accommodate solar, a battery and an EV charger will cost more than a basic replacement. We give you a free on-site quote, and the price is fixed before work starts.

On the job

  • A Chux electrician wiring an enclosure on an outside wall
  • An installer in hi-vis crouched on the roof, fixing a panel with a drill
  • A Chux team member with arms crossed in front of a Chux van

What you get.

  1. 01

    Board inspection

    We look at the condition of your existing board, the wiring behind it and how many circuits it carries before recommending anything.

  2. 02

    New switchboard

    A new board with a main switch, circuit breakers and safety switches (RCDs), laid out and labelled properly.

  3. 03

    Safety switch protection

    RCD protection on your power and lighting circuits, so a fault cuts the power fast instead of putting a person at risk.

  4. 04

    Circuit labelling

    Every circuit labelled so you or the next electrician can find what you need in seconds.

  5. 05

    Space for solar, battery and EV

    Room and capacity planned in, so adding solar, a battery or a charger later does not mean pulling it all apart again.

  6. 06

    Testing and compliance

    Full testing of the new board and the Certificate of Electrical Safety for the work.

Common questions

How do I know if my switchboard needs upgrading?

Look for ceramic fuses, no safety switches, frequent tripping, a burning smell, scorch marks or a full board with no spare space. Planning solar, a battery or an EV charger is another reason. An electrician can check it and tell you plainly whether it needs replacing or can stay.

How much does a switchboard upgrade cost in Geelong?

It depends on the number of circuits, the safety switches needed, the condition of the existing wiring and any extra capacity for solar, a battery or EV. We do not guess over the phone. We quote free on site and fix the price before work starts.

Can I get solar with an old switchboard?

Sometimes, but often the board must be upgraded first. The inverter needs a protected circuit and the board needs the right capacity and layout. If your board uses old fuses or is full, expect to upgrade it. We check this at the quote so there are no surprises.

How long does a switchboard upgrade take?

Many upgrades can be done within a day, with the power off for part of it. The time depends on the size of the board and any wiring that needs fixing. We tell you the expected outage when we quote so you can plan around it.

What is the difference between a fuse and a safety switch?

A fuse protects the wiring from overload by burning out. A safety switch detects leaking current, for example through a person, and cuts power in a fraction of a second. They do different jobs, and a modern board has safety switches as well as circuit breakers.

Do I need a safety switch on every circuit?

Current wiring rules require RCD protection on power and lighting circuits in new work. Older homes often have little or none. When we upgrade your board, we fit safety switches across your circuits so the whole house is properly protected.

Get a free on-site quote.

Tell us what you need. We reply within 24 hours. Solar, batteries, EV chargers and other installs get a free on-site quote with a fixed price in writing; repairs and fault-finding are charged by the hour.

Or call us

0490 503 073

Step 1 of 3: The job

What do you need?
Where is the job?
How do we reach you?

Install quotes are free, on site, no obligation. Repairs are charged hourly. We reply within 24 hours.