Skip to content
Chux Electrical Services

Powercor export limits and flexible exports explained

Powercor sets how much solar each address can export when your installer applies for pre-approval. If that comes back as zero, you can choose flexible exports instead, which lets an eligible system export up to its inverter limit or 10 kW most of the time. New systems also need an internet-connected, CSIP-AUS capable inverter.

By the Chux Electrical team. Updated 8 November 2026. 4 min read.

Wide view of new solar arrays across the roof, with safety rails in place

01

Who sets your solar export limit?

Your electricity network does. Powercor runs the network for most of the Geelong region, and we confirm the network for your address. Before a new solar system goes in, your installer lodges a pre-approval with the network, and the result sets how much the system is allowed to send back to the grid.

The export limit is separate from the size of your panels or inverter. A system can make more than it is allowed to export, and the rest is used in the house, stored in a battery or not produced.

02

What are flexible exports?

Flexible exports are Powercor's alternative to a low, fixed export limit. Instead of a static cap, the limit changes in real time to match how much room the network has. When there is spare capacity, eligible customers can export up to the limit of their inverter, or a maximum of 10 kW.

Powercor says a 12-month trial found customers exported freely more than 90% of the time. On rare occasions the network may reduce the flow from households to protect the network.

Drone view of the finished install, with neighbouring roofs around it

03

Who gets offered flexible exports?

If your solar pre-approval results in a 0 kW export limit, Powercor offers a choice between a flexible exports connection and a fixed 0 kW limit. Powercor lists these requirements:

  • A reliable internet connection and a compatible inverter.
  • For new installations since October 2024, an approved inverter that supports CSIP-AUS.
  • Where a property has more than one inverter, a compatible communications device to manage the whole site.
  • Devices that do not support CSIP-AUS must be set to a fixed zero export.

04

What is the emergency backstop?

Since 1 October 2024, new, upgraded and replacement solar systems in Victoria up to 200 kVA must be emergency backstop enabled. Solar Victoria says that means the system must be able to communicate using CSIP-AUS and be connected to the internet, with the inverter set up to talk to the network's utility server.

The backstop is a last resort that lets the network turn rooftop solar down or off when there is too much power in the grid. Solar Victoria says it will not affect the supply of electricity to your home. We set this up and test it as part of the install.

05

What if your inverter shows as disconnected?

Powercor says an inverter disconnected message usually means a temporary loss of communication, not a fault in your solar or battery. It only sends that notice after a week offline, so short internet dropouts do not trigger it. Its suggested steps:

  • Check your internet is working and the inverter is connected to it.
  • Check the inverter's app or online portal.
  • If both look fine, contact the inverter maker or your installer.

06

How much does an export limit matter now?

Less than it used to. Victoria has had no minimum feed-in tariff since 1 July 2025, so exported solar earns little and most of the value comes from using it yourself. That is why we size systems to your usage, not just the roof. See what size solar system a Geelong home needs, and if you already have solar, whether you can add a battery to store the surplus.

Common questions

What happens if my Powercor pre-approval says 0 kW export?

Powercor offers you a choice between a flexible exports connection and a fixed 0 kW export limit. Flexible exports need a compatible, CSIP-AUS capable inverter and a reliable internet connection. We talk you through which suits your system.

How much can I export on flexible exports?

Up to the limit of your inverter, or a maximum of 10 kW, when the network has room. Powercor says customers in its 12-month trial exported freely more than 90% of the time, and the network may reduce exports on rare occasions.

Does my solar inverter need the internet?

For new, upgraded and replacement systems in Victoria since 1 October 2024, yes. Solar Victoria's emergency backstop rules require the system to communicate using CSIP-AUS and be connected to the internet. Flexible exports also need a reliable internet connection.

Will the emergency backstop cut power to my house?

No. Solar Victoria says the backstop turns rooftop solar down or off as a last resort when there is too much power in the grid, and it will not affect the supply of electricity to your home.

Is Powercor the network for my address?

Powercor runs the network for most of the Geelong region, but not every address. We confirm your network on the free site visit, lodge the pre-approval for you as part of the install, and explain the export limit that comes back.

Get a free on-site quote.

Tell us what you need. We reply within 24 hours. Solar, batteries, EV chargers and other installs get a free on-site quote with a fixed price in writing; repairs and fault-finding are charged by the hour.

Or call us

0490 503 073

Step 1 of 3: The job

What do you need?
Where is the job?
How do we reach you?

Install quotes are free, on site, no obligation. Repairs are charged hourly. We reply within 24 hours.